Promag CON-485 Series Instrucciones de operaciones Pagina 21
- Pagina / 98
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Memo-Graph S 4 Wiring
Endress+Hauser 21
4.3 Connecting a device to the Ethernet (TCP/IP)
In principle, all devices equipped with an internal Ethernet interface can be integrated into a PC
network (TCP/IP Ethernet).
The device(s) can be accessed by any of the PCs in the network using PC software. It is not necessary
to install driver software ("COM redirection") on the PC because the PC software has direct access
to the Ethernet.
The system parameters "IP address", "Subnet mask" and "Gateway" are input directly at the device.
Changes to the system parameters are not activated until the SETUP menu is closed and the settings
accepted. Only then will the device work with the new settings.
!
Note!
It is not possible for several clients (PC) to communicate with a server (device) at the same time. If
a second client (PC) tries to establish a connection, he receives an error message.
4.3.1 Ethernet connection
An IEEE 802.3 compatible connector on a screened RJ45 plug on the rear side of the device is avai-
lable as a network connection. The device can be connected to a hub or switch via this connection.
The pin assignment corresponds to a standard MDI interface (AT&T258), so that a 1:1 cable with a
maximum length of 100 metres can be used here.
Figure 5: RJ45 socket (pin assignment AT&T256)
Meaning of the LED’s
There are three LEDs next to the Ethernet connections. These indicate the status of the Ethernet
interface.
Yellow LED: When the device is transmitting data it flashes irregularly, otherwise is continuously
on.
Green LED: When the device is receiving data it flashes irregularly, otherwise is continuously on.
Red LED: Is on when the device is connected to a network. If this LED is not illuminated then com-
munication is impossible.
The following standards are supported:
10BaseT, 10 MBit/s
The devices function according to the 10BaseT standard with 10MBit/s. It is, however, also pos-
sible to integrate the device into a 100BaseTx network via an auto-sensing hub or switch. This kind
of auto-sensing component sets itself automatically to the transmission rates supported by the end
device.
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Relacionado con productos y manuales para Herramientas de medición y de diseño Promag CON-485 Series
(40 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales